Menu
Cart 0

2001-2018 Ford / Mercury / 3-Button Remote Head Key /164-R8070 / FCC: OUCD6000022

19301935
  • $1985

Save to my Wishlist

Designed for 2011+ models, but backwards compatible with previous years. 

3 Button Ford Remote Head Key fob. 80 Bit NEW STYLE

NOTE: Some of our Ford remote head keys require separate programming for the remote portion. Simply perform the standard cycle key 8 times, press button process to program remote head.

Description

Designed for 2011+ models, but backwards compatible with previous years.

Works on the Following Models:
Ford Econoline 2004-2013
Ford Edge 2007-2015
Ford Escape 2005-2012
Ford Expedition 2003-2016
Ford Explorer 2001-2015
Ford Explorer ST 2001-2010
Ford F-150 2004-2014
Ford F-250 2004-2016
Ford F-350 2004-2016
Ford F-450 2011-2016
Ford F-550 2011-2016
Ford F-650 2011-2017
Ford F-750 2011-2017
Ford Five Hundred 2007-2011
Ford Flex 2009-2018
Ford Focus 2008-2011
Ford Freestar 2005-2007
Ford Freestyle 2005-2009
Ford Fusion 2006-2012
Ford Mustang 2011
Ford Ranger 2001-2011
Ford Taurus 2008-2009
Ford Taurus X 2008-2009
Ford Windstar 2001-2003
Lincoln MKS 2010
Lincoln MKX 2006-2013
Lincoln MKZ 2006-2013
Lincoln Mark LT 2011-2014
Lincoln Navigator 2014-2017
Mercury Mariner 2005-2010
Mercury Milan 2006-2010
Mercury Montego 2007
Mercury Monterey 2005-2007
Mercury Sable 2008-2010
Buttons: Lock
Unlock
Panic
Compatible FCC ID: CWTWB1U793
Compatible IC: 1788A-FWB1U793
OEM Part #(s): 164-R8067, 591256
Replaces: Rotunda 164-R8067
Rotunda 164-R8070
Rotunda 164-R8073
Strattec 5921186 (Ford Mustang)
Strattec 5912560 (Ford 3-Button)
Strattec 5915217 (Lincoln 3-Button)
Strattec 5915218 (Lincoln 4-Button)
Frequency: --
Chip: Tex 4D-63 80-Bit
Battery: CR2032
Emergency Key: Included
Test Blade: H75
Reusable: --
Condition: New AFtermarket

 

  • Onboard Programming: 

Immobilizer: Yes, w/ 2 original keys

Aftermarket - Remote Section On Board Programming

Programming Instructions: You Must have Two Master Working Keys (keys that came with the vehicle from factory.) to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! If you do have two working key and one of the keys are copies or clone key. The procedure below won’t work. Your New third (unprogrammed) key must also be cut prior to performing this procedure.

1. Insert an existing (working) key into the ignition cylinder.

2. Turn the ignition cylinder ON (Position 3) and back to OFF (Position 1). Ignition should stay in ON position for at least three seconds but no more than ten seconds.

3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition should stay in ON position for at least three seconds but no more than ten seconds.

4. Remove the second key, insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least six seconds and turn back to OFF.

5. If the new key has been successfully programmed it will start the vehicle and operate the remote keyless entry system. The theft indicator light will light up for three seconds to indicate the key was successfully programmed.

Remote Programming:

Obtain all remote transmitters for this vehicle. It's not necessary to re-program your working remote head keys as those will continue to work. If you are programming additional non-remote head key remotes for your vehicle then they must all be programmed during this procedure. You are able to program up to Four remotes in addition to your remote head keys. Do not depress the brake pedal during procedure.

1.Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)

2.Within 20 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 4.

3.Within 20 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 3. for all other remotes.

4.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.


We Also Recommend

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods